Exactly How to Replace a Tub in Your Bathroom
Exactly How to Replace a Tub in Your Bathroom
Blog Article
What are your opinions regarding How to Install a Bathtub?
Installing a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a new one is also a reasonably hard job. If the old tub is readily accessible, the task can relocate immediately; if you need to open up a wall surface to eliminate the old tub and position the brand-new bath tub, the task is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the brand-new one. See to it you have actually qualified on your own for the task and fit trying it. Instead of hiring a service provider to take control of a halfway-completed job, it is much better to consider employing one before you start. Possibilities are you may require an expert plumber to make tube connections.
This write-up will certainly help you install a brand-new tub in your bathroom if you have actually already acquired a brand-new tub and also don't need to transform the arrangement of your previous supply of water pipelines.
Your devices as well as product checklist need to consist of the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the faucets to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be rather problematic because of the restricted accessibility that is usually the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. Once the supply pipelines have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to moving on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin ensuring that the washers remain in area in between the faucet and the sink. Secure the tap in place with the maker given backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical tap ports. The previous kind needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wooden boards are useful in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the tub up until the spirit level reads level.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the proper supply pipe by making a compression join; then do the same for the various other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leakages and also tighten them if needed. Fill the bath tub as well as likewise inspect the overflow outlet and also the regular electrical outlet for leaks.
Lastly, fix the bathroom paneling as defined in the maker's user's manual. Tiling and also sealing around the bathtub needs to wait till the tub has been made use of a minimum of once as this will settle it right into its final position.
Planning for the Setup
Firstly, the sustaining structure supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the versatile faucet adapters to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its last position.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to split a rigid seal, triggering the water to pass through the wall surface between the bathroom and also the tiling, bring about complications with moisture and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and fittings. They are offered in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to always fill up the bath tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealer can fracture fairly early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily offered on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads on Tools You Need to Install a New Bathtub , I thought sharing that segment was a good idea. Make sure you take a moment to promote this blog entry if you liked it. Thank you for your time. Visit us again soon.
Contact Us Now Report this page